750 spirit harley wheel swap

[mmotofooll]

I am begining a rear wheel swap to 18 inch harley rear wheel and 200/50-18 rear tire. have allready obtained a rear caliper,rotor,sprocket,mastercylinder,and 3/4 axlebut would like any information on mastercylinder mounting or caliper stop instalation .thanks mmotofooll@aol.com

[AirportFF]

What type of caliper setup did you get?

[mmotofooll]

GMA BILLIT 2000 up soft tail.

[AirportFF]

What does the caliper bracket look like? I'm curious if it's similar to the one that's for the CBR rim conversion. Most folks just mount a block to the inside of the swingarm that will not allow the caliper mount to rotate forward or backward, but that still allows it to slide front to back to adjust the chain.

The master cylinder is usually mounted forward of the swingarm mount on the main frame rail. Then you will need to make an extension for the pedal linkage.

Pictures would be a great help. There are so many different parts out there without seeing them it's tough to help.

There was a website www.support135.com that had a step by step for a rear disc brake equipped CBR rim swap for the shadow. It doesn't seem to be up and running right now. I'll dig around and see what I can find on my computer for ya.

[mmotofooll]

I bought the caliper off ebay, but still have not received it yey.
the best I can tell it mounts on the rear axle.I have a picture off of this forum of a 750 ace with a 16 inch swap and he had used these parts, also had a brake stop mount made by canfly99 but unable to get clear image of mount. The rear mastercylinder Im using is from a cbr.

[AirportFF]

Try shooting Canfly a PM and see if he can get a couple pics for ya

Most of the info you need is on that other site. Are you a Delphi member? Go to
http://forums.delphiforums.com/SupportLocal135/start ask around there that's where the other site originated.

[cowboy]

I have the service manual with the cbr mod on it on disk.I think I can make ya a copy if you need it.

[AirportFF]

I have the service manual with the cbr mod on it on disk.I think I can make ya a copy if you need it.


Shit, I'll take one......how much ya want?

[mmotofooll]

That would be awsome if you could do that,let me know how much and ill give you my shipping info thanks.(Had tire mounted to wheel today,trial fitted it,looks BADD ASSS)

[cowboy]

It also has the harley wheel mod and cbr mod on it it says to use harley forward controls because they have a master cylinder for the break built in.If I can figure out how to copy the disk I will send you copys.Ill try to copy it this week and let you know.
leagal disclamer
All copys are for backup of your original copy only :wink_2:

[cowboy]

OK I got two disks ready to go.Email me your addresses and I will send them to you guys on monday.

[blackhawk]

i'm in. what'd you determine for cost?

[AirportFF]

OK I got two disks ready to go.Email me your addresses and I will send them to you guys on monday.


PM'd you my addy. Did you get it?

[cowboy]

PM'd you my addy. Did you get it?
Got it Ill send it to ya today.

[cowboy]

i'm in. what'd you determine for cost?
No charge, It dosn't cost me much for a cd & shipping.

[olpanrider]

hey cowboy, if it's not to much trouble put me on the list as well. I'll shoot back some cash to cover if ya give me an addy. "preciate man.

[AirportFF]

Cowboy you really opened up a can of worms now.........


BTW, Thanks I really appreciate it

[SmokeShowin]

Cowboy you really opened up a can of worms now.........


BTW, Thanks I really appreciate it

Like they said in "Spaceballs" - MERCHANDISING! May the schwartz be with you.

[mmotofooll]

Thanks for all your help Cowboy..........Mmotofooll.

[cowboy]

Glad to help.I sent airports out today.the rest I will send on wednesday.So if anyone wants one send me your address by tuesday night and Ill make copys and ship on wednesday.

[olpanrider]

sent ya the info that ya requested....thanks

[cowboy]

Cd's are in the mail.

[olpanrider]

Chris - got the CD today. Thanks alot man for taking the time, 'preciate it........Mike

[Partsguy198]

I ran out of worms so, I figured I'd open up a fresh can.

Anybody have a copy of this CD still around?

[Surfernick]

If you find someone with a copy - lemme know too, I'd like to get my hands on one. Thanks!

[cowboy]

I will see if I can make some more copys.Pm me the address you want them mailed to and when I get time to make copys Ill send them to ya.

[RustyJake]

Nice pic in your sig Nick. Bike looks awesome.

[jrod1970]

If you find someone with a copy - lemme know too, I'd like to get my hands on one. Thanks!

hey douch, where is the the guy that made your pipes?
:huh:

[Mr.Sinister]

hey douch, where is the the guy that made your pipes?
:huh: They look like Burbs. Do a SEARCH for Burbs pipe werks.

[Surfernick]

Nice pic in your sig Nick. Bike looks awesome.

Thanks!

[Surfernick]

hey douch, where is the the guy that made your pipes?
:huh:

They're Burbs from Burbspipewerks ya schmuck..

[mmotofooll]

bike is still for sal. had a buyer give a deposit,then damaged it on road testmdidnt want to buy it after they damaged it.
so needless to say its still for sale.has scratches on pipes,rad grille missing and damage to tire sidewall.havent messed with it for about 6months-to pissed.possiably might need some carb work?. no time to do anything except work.selling for 3500.00 as is has been stored inside under cover in shed .still nice,sick looking bike mods cost almost selling price.

[RAZOR]

bike is still for sal. had a buyer give a deposit,then damaged it on road testmdidnt want to buy it after they damaged it.
so needless to say its still for sale.has scratches on pipes,rad grille missing and damage to tire sidewall.havent messed with it for about 6months-to pissed.possiably might need some carb work?. no time to do anything except work.selling for 3500.00 as is has been stored inside under cover in shed .still nice,sick looking bike mods cost almost selling price.

DAMN IT I WISH I HAD THE MONEY
I WOULD BUY IT.... YOU FINANCE??:happy2:

[Corpsegrinder]

bike is still for sal. had a buyer give a deposit,then damaged it on road testmdidnt want to buy it after they damaged it.
so needless to say its still for sale.has scratches on pipes,rad grille missing and damage to tire sidewall.havent messed with it for about 6months-to pissed.possiably might need some carb work?. no time to do anything except work.selling for 3500.00 as is has been stored inside under cover in shed .still nice,sick looking bike mods cost almost selling price.

You mean to tell me the buyer took it for a ride and dumped it?? Did he compensate you in any way? I woulda been a mad motherfucker. Good luck with sellin it though.

[Surfernick]

I will see if I can make some more copys.Pm me the address you want them mailed to and when I get time to make copys Ill send them to ya.

Got the CD - thanks!!! It has all the info I needed.

[Surfernick]

hey douch, where is the the guy that made your pipes?
:huh:

They are Burbs...

[Gene Frenkle]

Just rip the disc with a program like Alcohol 120% and it will make an ISO image of the disc. Then use WinRAR to compress the ISO image into a RAR file. Just make sure you choose to break the compressed file into parts. Next upload the compressed RAR partfiles to http://www.filefactory.com/ Then come back here and post the links to each partfile that is located on filefactory and everyone can just download it. Even if everything I just said makes no sense, download the programs, RTFM and it will take you no time.

Or just send me a copy of the disc and I'll do it.

Fuck a bunch of mailing CD's. This is 2007 not 1987.

[Surfernick]

Yup...

[Stoney]

Hey cowboy i know your tired of sending these things out by now but i have been DYING to do this mod. If you could send me a copy id apprectiate it.
Thanks, Stoney

[Mad Tailor]

Looks like the only info on the swap is in that disk. Anyone??? I need it bad. Thanks

[Corpsegrinder]

Looks like the only info on the swap is in that disk. Anyone??? I need it bad. Thanks
Hey man. Sorry I didn't get back to ya. I'll give ya the run down on the harley setup. I'll type somethin up and send it to ya. Gimmie a few.

Edit: You have mail man :)

[kicknjunk]

If it is possible, could I maybe get some info on the harley swap as well. I am planning on putting a 21 out front and an 18 in back.

[Corpsegrinder]

If it is possible, could I maybe get some info on the harley swap as well. I am planning on putting a 21 out front and an 18 in back.

Search around the site for some answers. They're pretty much all there. If ya get stuck. Give a hollar. Theres way too many options to do a writeup. I could write a novel on the multiple ways you can set this up.

[rifleman223]

After serious deliberation, I actually decided to go wit the Buchanan's It was not a bad deal. I pick it up in 7 days. Can't wait....You guys are a great help. thanks especially to Corpsegrinder.

[fosno1]

It also has the harley wheel mod and cbr mod on it it says to use harley forward controls because they have a master cylinder for the break built in.If I can figure out how to copy the disk I will send you copys.Ill try to copy it this week and let you know.
leagal disclamer
All copys are for backup of your original copy only :wink_2:

Cowboy , would you send me a copy of the mods? I'll pay whatever!!

[Timmy67.5]

I smell a revival!

Cowboy, dude.... if you've got this laying around I'm happy to pay for your services to get a copy.

Can I get an amen?!

[lang]

I think you'll find what you need here:
http://www.spiritchopshop.com/chopshop1.html

[Timmy67.5]

Cool site! Thanks lang.